Skip to content

Hardwood Flooring

Start with the room. A concrete basement and an upstairs bedroom can call for different boards. Compare solid hardwood and engineered hardwood, then look at the grain, plank width and finish in your own light.

Morning light across pale oak floorboards beside a dining table

Browse by Type

Featured Hardwood Flooring

Solid oak and layered engineered flooring samples resting on a workbench

What the edge of a board tells you

A solid plank is one piece of wood all the way through. Turn over an engineered plank and you can see the real wood face above its supporting core. That layered construction limits seasonal movement. For a concrete slab, check the approved installation method. If you plan to refinish, ask how much of the wood face can be sanded.

See how the two constructions are installed when you compare solid and engineered hardwood.

Shop by Wood Species

Look at several boards together. Maple tends to have a fine, quiet grain. Hickory can move from pale cream to brown within one plank. For broad grain lines and visible knots, compare the grade and cut of two oak samples.

Hardwood Colors and Finishes

Take the samples to the room where the floor will go. Gray can pick up cool window light, and a brown board may look warmer beside cream cabinets. Check the samples again after dark. The guide to hardwood floor colors shows more tones side by side.

Pale maple and variegated hickory flooring samples side by side

Look at the grain in more than one board

Follow the grain on the maple and hickory samples, then lay several boards of the same species together. That shows the range a single piece can hide. If you prefer white oak, ask for its grade and compare knots and color changes against the product photos. Our white oak flooring guide explains what to look for.

Dark brown hardwood floor in a reading room with a low bookcase

Compare matte and satin in the room

Put a matte and a satin sample beside a window, then step back toward the doorway. Satin catches more of the light. Matte softens reflections, which can make small marks less obvious. Use our hardwood finish guide to compare sheen before choosing a stain.

Plan the floor for your room

A kitchen or a busy entry

Think about where water collects and where grit gets tracked in. In a kitchen, check the floor’s warranty for spills near the sink and dishwasher. In an entry, a grit-catching mat and a finish you can maintain matter more than stain color. Read about using hardwood in a kitchen.

A basement or heated slab

Ask the installer to identify the subfloor, test its moisture and check the floor’s approval for below-grade use. With radiant heat, the instructions for your exact board must also cover the heating system, adhesive and temperature limits.

From square feet to cartons

Add your installer’s allowance for cuts to the measured area. Then divide by the coverage per carton and round up. For example, Villa Caprisi Umbria covers 34.11 sq. ft. per carton. A 210 sq. ft. order total, including cuts, takes 7 cartons (238.77 sq. ft.). Other products have different carton sizes.

Hardwood Flooring Guides

View all articles

Hardwood Flooring FAQ

Choosing the boards

What is the difference between solid and engineered hardwood?

A solid board is milled from one piece of wood. An engineered hardwood plank has a real wood face over a bonded core. Choose a construction approved for the room, subfloor and installation method you plan to use.

How do I choose between oak, hickory and maple?

Lay several boards of each beside the cabinets or trim. Oak shows a distinct open grain, maple usually has finer markings, and hickory can have a broad range of light and dark tones. The white oak flooring guide also explains how grade and cut affect its appearance.

How do wide plank hardwood floors compare with narrow boards?

Mark two candidate widths on the floor with paper strips, then count how many rows cross the room. Narrow boards give you more seams. Wide boards let you see more of the grain in each piece. For a wide plank example, Villa Caprisi Umbria is 9½ inches across.

How does a matte finish compare with satin?

Matte gives a quieter reflection. Satin has a gentle sheen that is easier to see as you move past a window. Compare both samples under a lamp as well as in daylight. The hardwood finish guide shows what changes with sheen.

What is the difference between herringbone and chevron?

Herringbone uses rectangles meeting at right angles. Chevron uses angled ends that meet in a continuous V. For either pattern, confirm that the planks are made for the layout and that your installer has included border cuts. Compare herringbone and chevron layouts.

Rooms and installation

Can engineered hardwood go over concrete or in a basement?

Some engineered floors are approved for concrete and below-grade rooms. Ask the installer to test the slab for moisture, compare the result with the manufacturer’s limit and use the specified moisture-control system. Correct active leaks before installation.

Can I use hardwood with radiant floor heating?

Check the written instructions for the exact flooring and heating system. The approved installation method, temperature limits and start-up schedule can vary. Give the flooring instructions to the heating contractor before ordering.

Can hardwood be used in a kitchen?

Yes, if the product is approved for your project and spills are cleaned up promptly. Pay special attention to the dishwasher, sink and ice maker, where leaks can go unnoticed. Our guide to using hardwood in a kitchen covers the day-to-day trade-offs.

Which hardwood floors work well in a home with dogs?

A harder species can resist dents, but claws and tracked-in grit can still scratch the finish. A low sheen or visible grain can help small marks blend in. Keep nails trimmed and put a washable mat at the door. See our guide to white oak in homes with pets.

Ordering and care

How much extra flooring should I order?

Measure each part of the room, including closets you plan to floor. Ask the installer to add a cutting allowance for your layout and any spare boards you want to keep. Divide that total by the product’s square feet per carton and round up to a whole carton.

How long should hardwood acclimate before installation?

Use the instructions supplied with the floor. The room needs to be at its normal living conditions, and the installer may need to measure moisture in both the boards and the subfloor. Keep or open cartons as directed for that product.

Can engineered hardwood be refinished?

Sometimes. A professional can inspect the remaining wood above the joint and check whether earlier sanding or a textured surface limits what can be removed. A worn surface finish may be a candidate for recoating without a full sanding.

How should I clean hardwood flooring?

Sweep away grit or vacuum on a bare-floor setting. Wipe spills promptly and use a cleaner approved for the finish. Skip steam and wet mops because standing water can work into the joints. See our white oak cleaning guide for a routine you can use at home.